Showing posts with label Land Rover Range Rover (LM) V8-5.0L SC. Show all posts
Showing posts with label Land Rover Range Rover (LM) V8-5.0L SC. Show all posts

Friday, 2 November 2018

Land Rover Range Rover (LM) V8-5.0L SC Suspension - Air Suspension Height Connector/Sensor Harness Kit

*********************************************************************************** ********************************************************************************
2012 Land Rover Range Rover (LM) V8-5.0L SC Page 1

Vehicle: All Technical Service Bulletins Suspension - Air Suspension Height Connector/Sensor Harness Kit
LTB00447NAS1
23 JULY 2012

SECTION: 204

Air Suspension System Height Sensor Connector / Overlay Harness Kit Availability










AFFECTED VEHICLE RANGE:

CONDITION SUMMARY:

Situation: Air suspension system height sensor electrical connectors are now available as a serviceable part in the event of connector damage or corrosion causing an open or short circuit..

Action: In the event it becomes necessary to replace an air suspension system electrical connector, refer to the Repair Procedure outlined below.






PARTS:

TOOLS:
Refer to Workshop Manual for any required special tools

WARRANTY:

NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.


























DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.

Normal Warranty policies and procedures apply


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 2



















APPENDIX 1

REPAIR PROCEDURE

REPLACE AIR SUSPENSION SYSTEM HEIGHT SENSOR CONNECTOR

1. Refer to Workshop Manual, section 414-00: Battery and Charging System, and disconnect the battery ground cable.

  • Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. 2. Refer to Workshop Manual, section 100-02: Jacking and Lifting, and raise and support the vehicle.

  1. Refer to Workshop Manual, section 204-04: Wheels and Tires, and remove the necessary wheel and tire to access the affected air suspension system sensor.

LR4 AND RANGE ROVER SPORT FRONT HEIGHT SENSOR




















  1. Disconnect the damaged height sensor electrical connector.

    • Release any retaining clips required to allow access to the electrical connector during the repair.

LR4 AND RANGE ROVER SPORT REAR HEIGHT SENSOR


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 3
















  1. Disconnect the damaged height sensor electrical connector.

    • Release any retaining clips required to allow access to the electrical connector during the repair.

RANGE ROVER FRONT HEIGHT SENSOR















  1. Disconnect the damaged height sensor electrical connector.

    • Release any retaining clips required to allow access to the electrical connector during the repair.

RANGE ROVER REAR HEIGHT SENSOR





















  1. Disconnect the damaged height sensor electrical connector.

    • Release any retaining clips required to allow access to the electrical connector during the repair.

ALL VEHICLES

  1. Remove a suitable amount of wiring harness insulation as required to access the wiring.


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 4


























NOTE:
Cut only one wire at a time and stagger each joint to allow easier installation.

NOTE:
The colors of the overlay harness wires may vary.

NOTE:
Vehicles with adaptive damping have six (6); wires, vehicles without adaptive damping have three (3) wires.

  1. Cut the wire on the vehicle harness leading to cavity one of the height sensor connector in a suitable position and remove 10mm of insulation. (For connector location and pin identification, see Appendix 1 and refer to the relevant connector in the relevant Electrical Library).




























NOTE:
Make sure that the heat shrink is installed over the wire before crimping the connection.

  1. Using a suitable tool, crimp the connector to the height sensor harness. ^ Position the heat shrink over the height sensor harness.

NOTE:


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 5

The overlay harness should be cut so that there is no additional length added to the overall harness length after the repair.


























11. Using a suitable tool, remove 10 mm of insulation from the appropriate wire on the new height sensor harness connector.


























CAUTION:

Make sure that the surrounding components and trim are suitably protected when using the heat gun; failure to follow this instruction may result in damage to the vehicle.

  1. Using a suitable tool, crimp the connector to the appropriate wire on the new height sensor harness connector and secure the heat shrink.


NOTE:
Cut only one of the wires at a time and stagger each joint to allow easier installation.

NOTE:
Vehicles with adaptive damping have six (6) wires; vehicles without adaptive damping have three (3) wires.

  1. Carry out steps 9 - 12 for the remaining wires on the height sensor connector.

  1. Using a suitable tape, insulate the height sensor harness.

  1. Connect the height sensor electrical connector.


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 6


  1. If required, secure any wiring harness clips released for access.

  1. Refer to Workshop Manual, section 204-04: Wheels and Tires, and install the wheel and tire.

  1. Refer to Workshop Manual, section 414-00: Battery and Charging System, and connect the battery ground cable.

Land Rover Range Rover (LM) V8-5.0L SC Suspension System - Air Suspension Compressor Failure TECHNICAL BULLETIN LTB00491NAS1

*********************************************************************************** ********************************************************************************
2012 Land Rover Range Rover (LM) V8-5.0L SC Page 1

Vehicle: All Technical Service Bulletins
Suspension System - Air Suspension Compressor Failure
TECHNICAL BULLETIN
LTB00491NAS1
16 NOV 2012

SECTION: 204-05
Air Suspension System Compressor Failure

AFFECTED VEHICLE RANGE:
VIN: 6A198058 - CA393639
Range Rover (LM)
Model Year: 2006 - 2012

CONDITION SUMMARY:

Situation:
The air suspension system may be inoperative and Suspension Fault may be displayed in the message center.

Cause:
This may be cause by an air suspension system compressor failure due to over running

Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below.

PARTS:

LR041777 ................ Air compressor kit Qty: 1

TOOLS:

IDS with latest IDS-DVD and Calibration File; first available on DVD131.06 v.117 Land Rover-approved Midtronics Vehicle Power Supply Refer to Workshop Manual for any required special tools

WARRANTY:

NOTE:

Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.











DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.

Normal Warranty policies and procedures apply

REPAIR PROCEDURE

  1. NOTE: Do not carry out the air suspension system depressurize.
Refer to Workshop Manual section 204-05, steps 1-7 only, and replace the air suspension compressor.


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 2














2. Connect the air suspension pipe to the AMK compressor.




















  1. Install the four (4) air suspension system compressor retaining bolts. ^ Tighten to 10Nm (7.4 lbf ft).


















  1. Install the valve block assembly.
^  Connect the AMK harness connectors the same as the Hitachi compressor.















5. Install a new air suspension system compressor relay in the luggage compartment fuse box.


2012 Land Rover Range Rover (LM) V8-5.0L SC Page 3

  1. CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control modules in the vehicle.

CAUTION:

A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.

  1. Turn ignition 'ON' (engine not running).

  1. NOTE: IDS must be loaded with DVD131.06 v.117 or later.

Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.

  1. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.

  1. From the Session Type selection screen, choose 'Diagnosis'.

  1. Select the 'Selected Symptoms' tab, and then select:

    • Service Function

  1. Select 'continue'.

  1. Select the 'Recommendations' tab.

  1. CAUTION: During this procedure, if SDD presents a

question regarding compressor type, always select the type/manufacturer for the compressor being fitted to the vehicle as part of this repair, which under all circumstances should be an AMK compressor type. If unsure select 'EXIT' at this prompt and repeat this process after the facts are known. Failure to make the correct compressor type selection will cause SDD to install incorrect software. From the Recommendations tab, select 'Run' to perform the Air suspension - Air suspension compressor replacement function.

    • Follow all on-screen instructions to complete this task.

  1. Exit the current session.

  1. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.